Search results

S1000RR  FORUM

Help Support S1000RR FORUM:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. mike g

    Low beam not working.

    lights are controlled by the ecu in the instrument cluster if that helps?
  2. mike g

    New to me S1000 RR

    ventura is good
  3. mike g

    bikes away for the winter, new rad waiting to go on March or April time, see how the weather goes!

    bikes away for the winter, new rad waiting to go on March or April time, see how the weather goes!
  4. mike g

    tempreture

    i'm sure i've seen this info on here somewhere, but can't find it (gen 1) Fan comes on at 101 degrees goes off at ? Thermostat opens 85 degrees, closes ? TIA!
  5. mike g

    What previous bikes did you have?

    1974 Honda SS50 BSA B40 Triumph 350 Triton 750 RD350 x2 Triumph 650 (RD400 DT 250 DT175 x2 - still got 1) 1981 GS1000 (1100) (Bantam C15 GPZ550) GSX1100 Katana (1200) 1988 FJ1200 x2 Fireblade 2000 R1 4xv (still got) 2000 KDX250 (still got) 2006 FJ1200 (still got) 2010 GSXR1000 K6 2012 GSXR1000...
  6. mike g

    Remove rear wheel gen 3

    I have captive spacers which help and obviously bike is on paddock stand, agree pushing the pads apart helps, but only takes a couple of minutes to do it all, I sit behind and use my foot or a bar to lift the wheel up and then pop the spindle in, chain adjustment isn't changed from where it was
  7. mike g

    Piston Separator / Spreader on OEM Calipers

    I normally do one caliper at a time, pump the pistons out slightly, clean with brake cleaner spray and tooth brush, then they all push back with finger pressure. not needed to open bleed valves, but can see it could help. maybe still dirty if they won't go back? pop in new pads, pump up then do...
  8. mike g

    Gen 1 right hand switch problem

    some one on here does fixing the circuit boards - did mine a few years ago now LH side though
  9. mike g

    2018 Gen 3 Left side engine case fitting

    didnt wait or use threadlock
  10. mike g

    2018 Gen 3 Left side engine case fitting

    do not to drop oil if its on paddock stand. i just used grey silicone for the gasket. bolts are single use but ive reused mine a couple of times no problem
  11. mike g

    Clown bike

    k7 8 GSXR1000 are great bikes
  12. mike g

    Engine sliders vs covers

    I had the full RG covers on my Gen1 (by previous owner) but I've since changed the alternator and timing case to RG sliders, left the clutch on. I have had a number of stator failures, top coil burns out and wanted as much cooling to the bottom of the engine as possible, only done a year or so...
  13. mike g

    rear calliper

    4xv was first one then 5jj then fuel injected. it's now 25years old and will be doing a couple of vintage club runs this summer, before I part with it (thanks sadiq!). ive had since 2000 when it was just over a year old with 6000 miles on it. done over 60000 now, but not really used it since 2010.
  14. mike g

    rear calliper

    stick with it, great bike, had mine 9 years and love it. Funnily enough I'm just getting my old R1 (4xv) back on the road, it's been in the back of the garage since 2011 (when I got a GSXR) fuel system is horribly gummed up, still hoping to get it running today, will be interesting to see the...
  15. mike g

    rear calliper

    ouch brake is crap anyway!
  16. mike g

    rear calliper

    you need to take it apart and grease the pins with red rubber grease
  17. mike g

    Tyres Tyres Tyres

    lovely, been running corsas as go to tyre for years
  18. mike g

    Disconnect battery gen3

    mines on the original rectifier at 58000 miles, had a couple of stators though!
  19. mike g

    Any Nurburgring Trackdays?

    I did a course back there in the early nineties with PB it was great. If you can't find a track day there Spa is a great alternative.
Back
Top